Brezplačna poštnina Nitrous system AEM Water / Methanol Injection Controller Kit V3 - 4.3L | race-shop.si Povečaj

*282 007

AEM

AEM Water / Methanol Injection Controller Kit V3 - 4.3L

Injecting water or methanol is an easy, quick, and cost-effective way to improve the performance and reliability of your turbo or supercharged engine.

Nov izdelek

Dobavljivo po naročilu : 10+ks

Najkasneje na vašem domu: 23. 4.

650,60 € z DDV

AEM-30-3300   

Povpraševanje o izdelku

Povpraševanje o izdelku

AEM Water / Methanol Injection Controller Kit V3 - 4.3L

AEM Water / Methanol Injection Controller Kit V3 - 4.3L

Injecting water or methanol is an easy, quick, and cost-effective way to improve the performance and reliability of your turbo or supercharged engine.

Vprašanje o tem izdelku pošljite lastniku trgovine.

* Obvezna polja

  ali  Prekliči

Notify me about the stock

AEM Water / Methanol Injection Controller Kit V3 - 4.3L

AEM Water / Methanol Injection Controller Kit V3 - 4.3L

To be informed about product update via email, fill out the form.

* Required

  or  Cancel

Injecting water or methanol is an easy, quick, and cost-effective way to improve the performance and reliability of your turbo or supercharged engine.

Specifications:

  • Cost-effective way to improve performances
  • Better engine reliability
  • Lowers operating temperatures
  • Automatic triggering depending on boost (up to 1.5 bar)
  • Kit contents: control unit, pump, injector, 4.3L tank, MAP sensor, and installation hardware
  • AEM reference: 30-3300

 

The principle function of a water/methanol injection kit is very simple: an injector sprays water in the intake in the form of a very fine mist. The sprayed water instantly vaporizes in the intake: it is this change of state of the water (liquid state to gaseous state) which absorbs the heat of the air and reduces its temperature by several tens of degrees.

Water / Methanol Injection Advantages

  • The intake air is cooler and denser, allowing boost and ignition timing to be increased for better performance (without increasing the fuel's octane). AEM announces gains of up to 20% more power.
  • Knock is repelled, significantly improving the reliability of the engine.
  • Reduces exhaust gas temperature (EGT).
  • Descaling: the vaporization of water acts as a "steam cleaner", eliminating carbon deposits for better performance. This is particularly significant if your engine has an exhaust gas recycling system (EGR).

Note that no water particles will reach the cylinders, as the water is vaporized instantly. Methanol provides the same benefits as water in this application, with even greater efficiency. You can, therefore, use pure water (preferably demineralized or at least filtered) or a mixture of both up to 50% methanol concentration. For safety reasons, methanol being a highly flammable chemical, do not use in greater than 50% methanol concentrations.

Injector/nozzle location requirements :

  • The nozzle must be mounted above the tank (failure to do so may lead to fluid leaking or siphoning)
  • The nozzle must be installed before the throttle butterfly
  • Nozzle should also be mounted after the MAF sensor, if present, and after any intercoolers

Water / Methanol Injection kit Components

  • Control unit and electrical harness, allowing you to configure the automatic triggering (depending on boost or along a 0-5V input connected to an external source)
  • Robust, reliable, and quiet high-pressure water pump
  • Forged aluminum injector, supplied with three nozzles in various shapes to change flow rate (please check the installation manual to determine the flow that suits your needs)
  • 4.3L tank, compact design with anti-surge, equipped with a level probe (the information of which is sent to the control unit)
  • MAP sensor (2.5 bar absolute pressure)
  • Fitting accessories, hoses, bolts, etc...

Napiši mnenje

Napiši mnenje







  ali  Prekliči

Did not find your question?
Enter new question
Do you have a question? Search for an answer.

Moze li se narucit 1 komad? Kada bi bio dostupan za isporuku?

  Customer, 
08.10.2023, 
1 answer

Naravno, proizvod se naraučuje po komadu. Okvirni rok isporuke paketa je ispod svakog artikla od dana narudžbe.

  Admin, 
09.10.2023




category

Recent posts

Karbonske sani EVENTURI

Namestitev karbonskega dovoda EVENTURI na BMW F90 M5 COMPETITION LCI.
Read more
NAMESTITEV ŠPORTNEGA VOLANA

Kako namestiti športni volan? Kaj vse je potrebno in kakšne so prednosti? Več na blogu..
Read more
MEET & GREET RACE-SHOP

KAKO JE BILO?!
Read more
Kako je videti za vrati trgovine? Zakulisje iz RACESHOP-a.

DJ Lucky Boy je razkril, kako to deluje v naši državi, in se s fotoaparatom odpravil tja, kamor še nihče ni.
Read more
Pripnite se!

Varnostni pasovi izboljšujejo varnost in vizualni videz notranjosti za hobi in cestno uporabo.
Read more
Kakšno darilo izbrati za navdušenca nad tuningom?

Tipi daril za pod jelko!
Read more
Garaža za dirke: BMW E63 M6

Pro-drift BMW E63 M6 za sezono 2023
Read more
Plexiclick ® - "nevidni" nosilci registrskih tablic

Made in GERMANY
Read more
Mazda RX-7 FD RACE spec

TURBO WANKEL
Read more

Kategorije Proizvajalci

Zadnje ogledano

Nalagam...